No | Description | Part No | Qty | MOC |
---|---|---|---|---|
1 | Body | ITECHC/047/ROL/01 | 1 Nos. | Graded Cast Iron |
2 | Roller | ITECHC/047/ROL/02 | 2 Nos. | Carbon Steel Cadmium Plated |
3 | Roller Pin | ITECHC/047/ROL/03 | 2 Nos. | SS 316S |
RSL – 65 Drum Roller tunnion fabricated from steel , epoxy coated to resist corrosion, Roller are cadmium plated and equipped with bronze bushing for ease of drum rotation. Frame have holes in end to attached to floor via anchor bolts or lag anchors. One set of two tunnions are required for each container.
<Capacity | 2000 Kg |
Dimensions | 100 x 535 mm D x 110 mm H |
Weight | 25 Kg per set |
Note : isolation valve and mounting yoke assembly for use with chlorine, sulfur dioxide, gas or liquid.
Material : isolating valve-aluminum silicon bronze yoke-steel
This Print is the Property of Chlorotech Eng. Co. It is to be used only for the Purpose for which it was lent and must not be used in any way detrimental to the interest of this company and is subject to return on demand.
3/4” CARBON STEEL SCHEDULE 80 ASTM 106 Gr B
Drum gaseous chlorine manifold assembly complete with ¾” schedule 80 seamless carbon steel pipe work and ¾” forged steel 3000 lb fittings painted with yellow chlorine resister rubber paint for chlorine use, with manifold header valve (ISO/3224) 3/4” NPT inlet and 1.030-14 NGO out let.
The Hach CL17 Chlorine Analyzer uses colorimetric DPD chemistry to continuously monitor water for free or total residual chlorine. This low-cost analyzer provides a dependable and economical alternative to instruments that rely on costly electrodes or complex procedures. Unaffected by even large swings of pH, the CL17 performs an analysis every 2.5 minutes, 24 hours a day.
The CL17 offers both an alarm for manual chlorine feed control and a 4-20 mA output for automatic control of chlorine feed pumps for drinking water, wastewater and other water applications. Set for manual control, the instrument notifies the operator of out-of-limit chlorine levels - and allows manual intervention in the disinfection process as needed. The CL17 can be set for automatic control of chlorine feed pumps using one of two methods:
On-Off Control - Which turns the feed pumps on when chlorine levels fall too low for disinfection and off when levels rise above a pre-set limit.
Proportional Control – Which control the amount of chlorine in proportion to the strength of the CL17’s output signal. This done through the REC MIN and REC MAX keys. For automatic operation, the CL17 has one output control with a range of 4-20 MA, programmable over any portion of the instrument’s 0-5 mg/L range.
The unit is housed in an abs plastic case that is lightweight, shatterproof and corrosion resistant. The case includes built-in mourting bracket that simplify installation. Two windows clearly show chlorine measurements, alarms and reagent levels. A hinged door allows quick access to internal components.
Applications – Water, Wastewater and more
For drinking water application, the CL17 can be used to monitor the raw water stage to facilitate preoxidation, disinfection and the control of taste and odor problems. It can also be used at the
finished Water stage, where residual chlorine levels must be maintained during the distribution phase. For wastewater application, the CL17 has large tubing and fitting along with a self Cleaning By-Pass
Y-Strainer Kit to ensure continuous operation without clogging.
This Print is the Property of Chlorotech Eng. Co. It is to be used only for the Purpose for which it was lent and must not be used in any way detrimental to the interest of this company and is subject to return on demand.
(ISI MARK) As Per IS: 8523-1977 License No. CM/L-7024756 of superior quality Non Ageing Chemical Resistant Rubber With Double Reflex Sealing Flaps, Five Point Harness, Panoramic Replaceable Visor, Speech Diaphragm, Self- Demisting Facility, Inhalation and Exhalation Valves to en 148-1 Threading with Rubber Corrugated Tube, Pvc Carrying Strap With Jumbo Canister for Chlorine Max Conc. 20000 PPM 2% With ISI Mark.
No | Description | MOC |
---|---|---|
1 | SPINDEL | MONAL |
2 | BUSH | FORGED BRASS |
3 | GLANDE NUT | FORGED BRASS |
4 | GLAND PACKING | TEFLON |
5 | VALVE BODY | FORGED SILVER PLATED BRONZE |
6 | THREADS | ¾” BSP TAPER |
7 | MAKE | VANAZ/KOSAN/TECHNO/ASHA |
This Print is the Property of Chlorotech Eng. Co. It is to be used only for the Purpose for which it was lent and must not be used in any way detrimental to the interest of this company and is subject to return on demand.
Design for | Chlorine Service |
---|---|
Dial Size | 65mm to 150mm |
Range | 0-16 Kg/Cm2 |
Mounting | Bottom Connection mounting on Header Line |
Type | Chemical sealed diaphragm type with magnetic contact Chamber construction |
Top chamber type | Brass silver Plated |
Bottom chamber type | Brass silver Plated, Ti PTFE Padded (100% CL2 Service) |
Diaphragm | PTFE backed with Silver Foil |
Connection type | Bottom Connection |
Connection size | ½” NPT |
Type of glass | Laminated safety glass |
Liquid filled | Silicon Oil filled |
Dial marking | Black |
Design for | Water Service |
---|---|
Dial Size | 65mm to 150mm |
Range | 0-16 Kg/Cm2 |
Mounting | Direct Mounting/ Surface |
Connection type | Bottom Connection |
Connection size | ½” NPT |
Type of glass | Laminated safety glass |
Dial marking | Black |
Casing | Bottom Connection |
Connection size | +/- 1% |
Weather Proof | Yes |
Design for | Chlorine Service |
---|---|
Dial Size | 100mm |
Range | 0-750 mm in Hg |
Mounting | Panel Mounting |
Type | Chemical sealed diaphragm type |
Top Chamber Type | PVC |
Bottom Chamber Type | PVC |
Diaphragm | Viton |
Connection Type | Bottom Connection |
Connection Size | ¼” NPT |
Type of glass | Crystal Clear plastic, Snap-fit |
Liquid filled | Silicon Oil Filled |
Dial marking | Black |
Casing | SS case |
Gas to be detected | Chlorine gas |
---|---|
Range / Resolution | 0 to 20 PPM |
Accuracy | ±1% of the full scale value. |
Sensor type | Long life Electrochemical sensor, Imported make |
Sensor life | Expected 2 year for Electrochemical sensor. |
Set point | Two independent set point, LO & HI with blinking indication with programmable latch/non-latch facility only for indication purpose. (There is no relay output) |
Display | Easy- to-read 0.5”, 3.5 digit LCD Display |
Setting | Setting by 4 keys on front panel i.e. ‘SET / NEXT’, ‘UP’, ‘DOWN’ & ‘TEST / BACK’ keys. |
Loop output | 4-20mA, with permissible load 750 ohm at 24Vdc, 25mA. |
Monitoring | i) By display : Shows “Err” indication. Sensor Open/Over Indication ii) By loop current : Selectable, upscale current : 22mA, Down scale current : 3.6mA to 3.8mA. |
Supply Voltage | 14VDC to 36VDC, normally 24 VDC, 25mA |
Digital filter | Select damping factor 1 to 99 to smooth input signal. |
Operating ambient Temperature | 0 to 50 degree C ± 5% |
Relative humidity | Below 95%, non condensing. |
Sensor Housing | P.V.C. |
Enclosure Detail | FLAMEPROOF , Cast Alluminium alloy, LM-6 / C.I Enclosure, IP-65, As per IS : 2148 – 1981, 145mm (Dia) X 130mm (Height) X 85mm (D) Mounting : Wall Mounting / Stand Mounting, 250 Grams |
Model | TOX-107-FLP |